PTP Timestamping Resolution

8 ns

Supported timing protocol

PTP according to IEEE 1588–2008 (IEEE 1588 Version 2)

PTP (IEEE 1588) Features

• Default profile IEEE 1588-2008, Annex J
• End-to-end (multicast) and peer-to-peer delay mechanisms
• PTP over UDP/IPv4, UDP/IPv6 and Ethernet/IEEE 802.3
• (IEEE 1588-2008 Annex D, E, and F)
• Power profile according to IEEE C37.238-2011 (IEEE profile for use of IEEE 1588-2008 Precision Time Protocol in power systems applications)
• Power profile IEEE C37.238-2017 (IEEE profile for use of IEEE 1588-2008 Precision Time Protocol in power systems applications)
• IEC/IEEE 61850-9-3:2016

Holdover performance

Holdover drift in 24 hours at constant temperature, after 48 hours of operation:

• With high precision oscillator (OCXO-25): < 25 µs
  (measured values < 4 µs)

10 MHz

• BNC connector
• Sinusoidal
• 50 Ohm output impedance
• 4 dBm (1 Vpp) ±2 dBm at 50 Ohm load
• Short circuit protected
• Ground connected to housing

Out 1, Out 2

• BNC connector
• 50 Ohm output impedance
• Unmodulated (digital) time codes: 2.5 V at 50 Ohm load, 5 V at open circuit, TTL compatible
• Modulated IRIG-B: 3 V amplitude (peak) at 50 Ohm load, 6 V amplitude at open circuit
• Short circuit protected
• Ground connected to housing

Out 3

• Screw terminal
• Optocoupler Darlington output
• Maximum collector-emitter voltage: 30 V
• Maximum current: 100 mA
• Pulse delays
  ton < 3 µs (at all load impedances)
  toff < 20µs (at 30 VDC, load impedance < 1 kOhm)
• Supports digital (unmodulated) time codes

Out 4, Out 5

• Fiber optical output
• ST connector
• Wavelength 820 nm
• Compatible with 50/125 µm, 62.5/125 µm, 100/140 µm fibers and 200µm plastic-clad silica (PCS) fibers
• Support digital (unmodulated) time codes

IRIG-B

• TAI, UTC or local time base
• Unmodulated (IRIG-B00x) or
• 1kHz Modulation (IRIG-B12x)
• Coded expressions: Control functions,
• Straight binary seconds, BCD YEAR

DCF77

• Unmodulated DCF77 time code
• CET / CEST time base

PPX

• TAI, UTC or local time base
• 1, 10, 100, 1000 PPS, 1 PPM, 1 PPH
  or custom period
• Custom period between:
  10 mHz to 2.048 MHz (at output 1 and output 2)
  10 mHz to 10 kHz (at output 3)
• Custom pulse width (>10ns)
• Falling or rising edge
• Can be combined with Trigger

Trigger

• TAI, UTC or local time base
• Absolute trigger date and time programmable with 1s resolution
• Can be combined with PPX

Management

• Web Interface (HTTP/HTTPS)
• TFTP, FTP, and SSH access
• Automated configuration via SSH, SOAP and XML files
• Fail-safe software upgrade in the field
• Email notifications
• Syslog (local and remote)

Networking

• Twisted pair (10BaseT/100BaseTX, RJ45) and optical Ethernet (100BaseFX, LC, multimode) connectors. One interface useable at a time.
• Supports IPv4 and IPv6
• Power over Ethernet according to IEEE 802.3af
• DHCP
• Zeroconf (MDNS/DNS-SD)

USB

• USB 2.0 (Type B)
• USB network gadget (RNDIS)
• Allows network connection to the TICRO 100 and devices attached to TICRO 100's Ethernet interface (with USB only IPv4 is supported @ the moment)

Power over Ethernet

• Max. power consumption 13W
• Powered Device (PD) class 3 according to IEEE 802.3af
• Operates as PSE (power sourcing equipment) according to IEEE 802.3af when powered via front or back panel DC input.
• Capable of supplying a class 1 PD (up to 4W).

Front panel DC input

• 18-57 V DC
• power consumption <15W
• Terminal block, maximum conductor cross section 1.5 mm²

WARNING: Product safety according to IEC 61010?1 and IEC 60255-27 only achieved by using an external power supply unit that complies with the SELV standard.

Back panel DC input

• 18-57 V DC, power consumption <15W
• power consumption <15W
• barrel connector
• WARNING: Back panel DC input does not fulfil the surge requirements of IEC 60255-27. Use the front panel DC input if compliance with IEC 60255 is required.
  WARNING: Product safety according to IEC 61010-1 only achieved by using an external power supply unit that complies with the SELV standard.

General

• Radiated emissions according to EN 61326-1, CISPR 11, IEC 60255-25, EN 55022, class A, 30 MHz - 6 GHz
• Radiated emissions according to FCC part 15 class A, 30 MHz - 6 GHz
• Radiated immunity according to EN 61326-1, EN 61000-4-3, IEC 60255-22-3: 80 MHz – 3 GHz, AM 1 kHz, m=0.8, 10 V/m
• ESD according to EN 61326-1, EN 61000-4-2, IEC 60255-22-2: contact discharge ±6 kV, air discharge ±8 kV

Front panel DC input

• Conducted immunity continuous wave according to EN 61326-1, EN 61000-4-6, IEC 60255-22-6, 150 kHz - 80 MHz, AM 1 kHz, m=0.8, 10V, spot measurements at 27 MHz, 68 MHz
• EFT (Burst) according to EN 61326-1, EN 61000-4-4, IEC 60255-22-4: 5/50 ns, 5 kHz, 1 minute, ±2 kV
• Surge according to EN 61326-1, EN 61000-4-5, IEC 60255-22-5: Line-Line ±1 kV, Line-PE ±2 kV
• ESD according to EN 61326-1, EN 61000-4-2, IEC 60255-22-2: contact discharge ±6 kV

Back panel DC input

• Conducted immunity continuous wave according to EN 61326-1, EN 61000-4-6, IEC 60255-22-6, 150 kHz - 80 MHz, AM 1 kHz, m=0.8, 10V, spot measurements at 27 MHz, 68 MHz
• EFT (Burst) according to EN 61326-1, EN 61000-4-4, IEC 60255-22-4: 5/50 ns, 5 kHz, 1 minute, ±2 kV
• Surge according to EN 55024, EN 61000-4-5: Line-PE ±0.5 kV
• ESD according to EN 61326-1, EN 61000-4-2, IEC 60255-22-2: contact discharge ±6 kV

Ethernet port (RJ45)

• Conducted emission according to EN 55022, IEC 60255-25, 150 kHz – 30 MHz, class A
• Conducted immunity continuous wave according to EN 61326-1, EN 61000-4-6, IEC 60255-22-6, 150 kHz ? 80 MHz, AM 1 kHz, m=0.8, 10V, spot measurements at 27 MHz, 68 MHz
• EFT (Burst) according to EN 61326-1, EN 61000-4-4, IEC 60255-22-4: 5/50 ns, 5 kHz, 1 minute, ±4 kV
• Surge according to EN 61326-1, EN 61000-4-5, IEC 60255-22-5: Line-PE ±1 kV
• ESD according to EN 61326-1, EN 61000-4-2, IEC 60255-22-2: contact discharge ±6 kV

Ethernet port (Fiber)

• ESD according to EN 61326-1, EN 61000-4-2, IEC 60255-22-2: contact discharge ±6 kV

10 MHz, Out 1, Out 2, Out 3

• Conducted immunity continuous wave according to EN 61326-1, EN 61000-4-6, IEC 60255-22-6, 150 kHz - 80 MHz, AM 1 kHz, m=0.8, 10V, spot measurements at 27 MHz, 68 MHz
• EFT (Burst) according to EN 61326-1, EN 61000-4-4, IEC 60255-22-4: 5/50 ns, 5 kHz, 1 minute, ±4 kV
• ESD according to EN 61326-1, EN 61000-4-2, IEC 60255-22-2: contact discharge ±6 kV

Out 4, Out 5

• ESD according to EN 61326-1, EN 61000-4-2, IEC 60255-22-2: contact discharge ±6 kV

USB port

• Conducted immunity continuous wave according to EN 61326-1, EN 61000-4-6, IEC 60255-22-6, 150 kHz ? 80 MHz, AM 1 kHz, m=0.8, 10V, spot measurements at 27 MHz, 68 MHz
• EFT (Burst) according to EN 61326-1, EN 61000-4-4, EN 55024: 5/50 ns, 5 kHz, 1 minute, ±1 kV
• ESD according to EN 61326-1, EN 61000-4-2, IEC 60255-22-2: contact discharge ±6 kV

Operating temperature range

-20°C … +50°C (-4°F … + 122°F)

Storage temperature range

-40°C … +85°C (-40°F … +185°F)

Climate

Tested according to IEC 60068-2-30, Test Db, damp heat,
cyclic (6 cycles, 55°C)

Vibration

Tested according to IEC 60068-2-6 and
IEC 60255-21-1 (class 1).

• Response: frequency range 10…150 Hz, 0.5 g, 1 sweep cycle per axis
• Endurance: frequency range 10…150 Hz, 1 g, 20 sweep cycles per axis

Shock

Tested according to IEC 60068-2-27 and
IEC 60255-21-2 (class 1)

• Response: 5 g/11 ms, half-sinusoid, 3 pulses in each direction, 6 directions
• Withstand: 15 g/11 ms, half-sinusoid, 3 pulses in each direction, 6 directions
• Bump test: 10 g/16 ms, half-sinusoid, 1000 pulses in each direction, 6 directions

Housing type:

IP40 according to IEC 60529

Dimensions

H x W x D: 54.6 x 171.6 x 121 mm / 2.15” x 6.75” x 4.76”
(without accessories)

Weight

<750 g / <1.65 lbs