Technical Data - Bode 100
The technical data shown below applies to Bode 100 - Revision 2. A complete datasheet in pdf form for Bode 100 Revision 2 ad well as for Bode 100 - Revision 1 can be downloaded at the end of this page.
| Characteristic | Rating |
|---|---|
| Frequency range | 1 Hz to 50 MHz |
| Waveform | Sinusoidal |
| Signal level range | -30 dBm to 13 dBm |
| Source level accuracy | ± 0.3 dB ( 1 Hz to 1 MHz) ± 0.6 dB ( 1 MHz to 50 MHz) |
| Source level frequency response (flatness) | ± 0.3 dB (typical, referring to 10 MHz) |
| Frequency accuracy after adjustment | ± 2 ppm ± quantisation error ( = 0.5 ∙ step size ) |
| Frequency stability | ± 2 ppm (< 1 year after adjustment) |
| Frequency step size / resolution | 0.00605 Hz (1 Hz to 100 Hz) 0.03632 Hz (100 Hz to 50 MHz) |
| Source impedance | 50 Ω |
| Return loss (1 Hz to 50 MHz) | > 30 dB, > 35 dB (typical) |
| Spurious signals & harmonics | < -55 dBc (typical) |
| Maximum reverse signal / power | 0.5 W = 5 VRMS (≤ 3.3 Vdc recommended) |
| Connector type | BNC |
| Characteristic | Rating | |
|---|---|---|
| Frequency range | 1 Hz to 50 MHz | |
| Input impedance (software switchable) | High: 1 MΩ (ac-coupled) | |
| 1 MΩ input impedance | 1 MΩ ± 2% || 40...55 pF | |
| 50 Ω input impedance return loss | > 28 dB, > 35 dB typical (1 Hz to 50 MHz) | |
| Receiver bandwidth (RBW) software selectable | 1 Hz, 3 Hz, 10 Hz, 30 Hz, 100 Hz, 300 Hz, 1 kHz, 3 kHz, 5 kHz | |
| Input attenuators (software selectable) | 0 dB, 10 dB, 20 dB, 30 dB, 40 dB | |
| Full-scale ac input signal | 100 mVRMS @ 0 dB input attenuator 316 mVRMS @ 10 dB input attenuator 1 VRMS @ 20 dB input attenuator 3.16 VRMS @ 30 dB input attenuator 10 VRMS @ 40 dB input attenuator | |
| Input channel sensitivity | 1 µVRMS @ 0 dB attenuator, 10 Hz RBW (typical) | |
| Maximum dc voltage (1 MΩ input impedance) | 50 V | |
| Maximum dc voltage (50 Ω input impedance) | 7 V | |
| Input channels dynamic range | > 100 dB (@ 10 Hz RBW) | |
| Noise floor (S21 measurement) RBW = 10 Hz, PSOURCE = 13 dBm, Attenuator CH1: 20 dB, CH2: 0 dB | 1 Hz to 10 kHz: -115 dB (typical) 10 kHz to 10 MHz: -125 dB (typical) 10 MHz to 50 MHz: -105 dB (typical) | |
| Gain error | < 0.1 dB (User-Range calibrated) | |
| Phase error | < 0.5° (User-Range calibrated) | |
| Connector type | BNC | |
| Characteristic | Minimum Configuration |
|---|---|
| Processor | Intel Core-I Dual-Core (or similar) |
| Memory (RAM) | 2 GB, 4 GB recommended |
| Graphics resolution | Super VGA (1024x768) higher resolution recommended |
| Graphics card | DirectX 11 with Direct2D support |
| USB interface | USB 2.0 or higher |
| Operating system | Windows 10 & 11 |
Note: Bode 100 Revision 2 devices require Bode Analyzer Suite 3.00 or newer.
| Wide-range mains power adapter | |
| Input voltage / frequency | 100…240 V / 47…63 Hz |
| Output voltage / current | 18 Vdc / 1 A |
| Bode 100 power requirements | |
| Supply voltage range | +9 Vdc to +24 Vdc |
| Power demand | < 10 W |
| Supply current | at 12 V: 580 mA (typical) at 18 V: 390 mA (typical) at 24 V: 290 mA (typical) |
| Low supply voltage shut-down | 8.25 V (typical) |
| Power connector / socket | Coaxial power socket Inner diameter 2.5 mm Outer diameter 5.5 mm |
| Connector polarity | Inner connector ... positive |
| Characteristic | Condition | Rating |
|---|---|---|
| Temperature | Storage | –35…+60ºC/–31…+140ºF |
| Operating | +5…+40ºC/+41…+104ºF | |
| For specifications | 23ºC ± 5ºC/73ºF ± 18ºF | |
| Relative humidity | Storage | 20…90%, non-condensing |
| Operating | 20…80%, non-condensing |
| USB connector | Type B |
| Dimensions (w × h × d): | 26 x 5 x 27 cm 10.25 x 2 x 10.65 inch |
| Weight - Bode 100: | 1.9 kg / 4.2 lb |
| Weight - Accessories: | < 0.5 kg / 1.1 lb |
| Maximum supply voltage | +28 Vdc |
| Maximum supply reverse voltage | -28 Vdc |
| Maximum input signal at CH1 or CH2 (low impedance, 50 Ω) | 1 W (= 7 VRMS) |
Maximum ac input signal at CH1 or CH2 | 50 VRMS 1 Hz to 1 MHz 30 VRMS 1 MHz to 2 MHz 15 VRMS 2 MHz to 5 MHz 10 VRMS 5 MHz to 10 MHz 7 VRMS 10 MHz to 50 MHz |
| Maximum dc input signal at CH1 or CH2 (high impedance, 1 MΩ) | 50 V |
| Maximum return power at the OUTPUT connector | 0.5 W (= 5 VRMS) |
